A Guide for putting together PuzzleLock Sewers

an overhead rendering of PuzzleLock Sewer

A couple of users have asked me for a guide to laying out their PuzzleLock Sewers to match the example in the product video. I can see how it could be a little confusing until you have enough tiles printed out to be able to play with it and see how you can configure it.

photo of printed and painted set

In the video, you can’t really see all of the puzzlelock connections. This is a good thing–unless you are having to freeze frame to figure it out… So here are some call outs for the pieces you need to configure the large area that I show leading to a large arch inspired by the “Cloaca Maxima” of the sewers of ancient Rome.

Cloaca Maxima

The normal passageway through the sewers is 6″ across. The “wall” sections (3 types) have a 1″ wide ledge that would be the walkway when the sewers are full of water. Between the walls is a 2″ square tile. There are bridge tiles that can cross the entire span, and “end” tiles that can cap off a passage:

For smaller printers, there are split bridges and split ends
The stairs on Column B and Wall C give access from the surface streets all the way down to the lowest level.

The Sewer_Column_A and Sewer_Column_B should be places symmetrically across from each other on a passageway to create the impression of an arch across the passage (though the height of all pieces is cut off at 70mm).

I hope this is helpful! If you have not purchased the .STL files they are available here for only $19.95

PuzzleLock Playsets

IMG_4738

In February, I debuted the PuzzleLock Caves and PuzzleLock Dungeon at Con Nooga in Chattanooga. The response was very good, so tomorrow we are launching a Kickstarter to fund the creation of more PuzzleLock playsets!

These playsets are 28mm scale terrain for tabletop role-playing games like Dungeons & Dragons. They help create an immersive gaming experience. They are printed on a $200 home 3D printer, and I printed the entire dungeon on a $20 roll of filament!

Unlike other systems, PuzzleLock doesn’t require any clips or magnets. It goes together like a jigsaw puzzle!

Caves_promo2
Untitled-2
Untitled-5

The Caves are 100mm point to point and about 35mm tall. The sides of the hexagons are 50.8mm (2″) and can connect to any other PuzzleLock playset.

PuzzleLock Caves

There are 24 tiles including entrances Tiles are ~100mm point to point and ~35mm tall. The sides of the hexagons are 50.8mm (2").

$19.95

The PuzzleLock Caves are available NOW at Cults3D:
https://cults3d.com/en/3d-model/game/puzzlelock-caves

Also available at DriveThruRPG:
https://www.drivethrurpg.com/product/267106/PuzzleLock-Caves

Dungeon_promo2
Untitled-3
The Dungeon set includes a “stair jack” for placing minis on the steps, and also a couple of “grid-painting” jigs for gamers who prefer a 1″ grid on their tiles.
Untitled-4
Untitled-6

The dungeon tiles are 50.8mm ( 2″) square, and about 35mm tall. They work with all other PuzzleLock Tiles.

PuzzleLock Dungeon

There are 58 files including working doors and portcullis, torch sconces, trapdoors, stairs, pillars and dias Tiles are based on 50.8mm squares (2") with 32mm walls, ~35mm tall overall.

$19.95

Dungeons are available NOW
on Cults3D:
https://cults3d.com/en/3d-model/game/puzzlelock-dungeon
on DriveThruRPG:
https://www.drivethrurpg.com/product/267145/PuzzleLock-Dungeon

All of the PuzzleLock playsets are delivered as .STL files, which are 3D models that can be printed on a home 3D Printer.

IMG_4469

The Kickstarter was 857% funded! Stretchgoals for Traps & Secret Doors and Sewers & Undercity were unlocked and will be available on DriveThruRPG and Cults3D after they are sent to backers.